0
Call Toll Free :

1 (888) 897-4263

We Accept :

Shane Coatings -
WOODSHIELD

WOODSHIELD Ultra-Premium 100% Acrylic
Exterior Low Sheen Ultra-Low VOC Paint

$375.95 (5 Gallons) & $260 Shipping
Minimum Order 25 Gallons (Any Product)

Product Description :

WOODSHIELD™ – Low sheen finish.

This Ultra-Premium exterior, Ultra-Low VOC, 100% acrylic paint provides MAXIMUM PROTECTION against UV color fade, mildew, efflorescence, water intrusion, and film failure (grain-cracking, peeling, blistering).

Additional Product Information

WOODSHIELD™ Low Sheen paint can be used on properly prepared and primed masonry, concrete, tilt-up, block, stucco, plaster, wood, and metal.

Advanced technology and premium ingredients provide unparalleled performance, durability, coverage, and adhesion. Can be used down to surface and air temperature of 35ºF.

Performance Properties:
  • Maximum Protection Against UV Color Fading
  • Maximum Protection Against Mildew
  • Maximum Protection Against Efflorescence
  • Maximum Protection Against Water Intrusion
  • Maximum Protection Against Grain-Cracking,
  • Maximum Protection Against Peeling & Blistering
  • Low Sheen Finish
  • Ultra-Low VOC Eco-Friendly
Surfaces to Use on:
  • Use Only on Primed Surfaces
  • Masonry
  • Concrete
  • Concrete Block
  • Plaster
  • Wood
  • Metal
Recommended Primer:

ELASTO-SEAL/BOND KOTE 260™

Premium Primer Bonder

Areas to Use:
  • Most Exterior Surfaces
  • Do Not Use as a Roof Coating
  • Previously Painted Surfaces
  • Exterior Walls
  • Exterior Ceilings
  • Fascia Boards
  • Doors
  • Window Trim
  • Commercial Properties
  • Residential Properties
  • And More
Packaging:

5 Gallon Bucket

Surface Preparation:
  • Before applying WOODSHIELD™ all surfaces must be cured, clean, dry, and free from dirt, dust, rust, stains, grease, oil, mildew, wax, efflorescence, bond-breakers, and other contaminants.
  • Remove all loose, peeling, or chalky paint by sanding, scraping, or other appropriate methods.
  • Repair all cracks, holes, and other surface imperfections with a suitable patching material.
  • Repaired surfaces should then be sanded smooth and dusted clean. Glossy surfaces should be dulled to provide a roughened surface for good adhesion
Apply With:

Brush, Roller, Airless Spray

Thinning Recommendation:

This coating is intended to be applied without thinning or diluting under normal environmental and application conditions. If necessary to maintain good workability, add up to 1/4 pint (4 fl. oz.) of clean water per gallon of coating.

Health & Safety:

Use in a well-ventilated area. Never scrape old paint without proper protective equipment. Scraping or sanding surfaces of older buildings may release dust containing lead or asbestos. EXPOSURE TO LEAD OR ASBESTOS CAN BE VERY HAZARDOUS TO YOUR HEALTH. Always wear appropriate personal protective equipment during surface preparation, and finish cleanup of any residues by water-washing all surfaces.

In Case of Eye Contact:

Flush immediately with plenty of water for at least 15 minutes and get medical attention.

Avoid prolonged contact with skin. Wash paint from your skin with soap and water. Replace lid on container tightly after each use.

Storage:

CAUTION! Do not freeze. Store in a cool, dry area out of direct sunlight. Protect from elements and from temperatures above 110 °F. Close container tightly when not in use.

Keep out of reach of children

LIMITED LIFETIME WARRANTY:

SC Manufacturing LLC warrants your complete satisfaction with this product from defect as long as you own or reside in your residence when our product has been applied and maintained according to exact label directions.

We do not warrant problems with the product which are caused by factors beyond our control, such as structural defects, damage to the paint film by others, poor condition of the substrate, improper application, etc.

If not satisfied as warranted, return the unused portion, as well as a sales receipt to the place of purchase. You will receive as your exclusive remedy either from a refund of the price paid for the product, or replacement with a product of equal value.

This product warranty specifically excludes labor or cost of labor for the application of any paint and consequential, incidental damages. However, the warranty is only valid if applied by a Shane Coatings™ certified technician.

Some states do not allow the exclusion of consequential or incidental damages, so the limitation or exclusion contained in the above warranty may not apply to you.

This warranty gives you specific legal rights, and you may have other rights that vary from state to state.

Warranty is backed by SC Manufacturing LLC, a subsidiary of The Shane Coatings Company.

$375.95 (5 Gallons)
& $260 Shipping

Minimum Order 25 Gallons

$
Add to Wishlist
Add to Wishlist
Additional Product Information

WOODSHIELD™ Low Sheen paint can be used on properly prepared and primed masonry, concrete, tilt-up, block, stucco, plaster, wood, and metal.

Advanced technology and premium ingredients provide unparalleled performance, durability, coverage, and adhesion. Can be used down to surface and air temperature of 35ºF.

Performance Properties:
  • Maximum Protection Against UV Color Fading
  • Maximum Protection Against Mildew
  • Maximum Protection Against Efflorescence
  • Maximum Protection Against Water Intrusion
  • Maximum Protection Against Grain-Cracking,
  • Maximum Protection Against Peeling & Blistering
  • Low Sheen Finish
  • Ultra-Low VOC Eco-Friendly
Surfaces to Use on:
  • Use Only on Primed Surfaces
  • Masonry
  • Concrete
  • Concrete Block
  • Plaster
  • Wood
  • Metal
Recommended Primer:

ELASTO-SEAL/BOND KOTE 260™

Premium Primer Bonder

Areas to Use:
  • Most Exterior Surfaces
  • Do Not Use as a Roof Coating
  • Previously Painted Surfaces
  • Exterior Walls
  • Exterior Ceilings
  • Fascia Boards
  • Doors
  • Window Trim
  • Commercial Properties
  • Residential Properties
  • And More
Packaging:

5 Gallon Bucket

Surface Preparation:
  • Before applying WOODSHIELD™ all surfaces must be cured, clean, dry, and free from dirt, dust, rust, stains, grease, oil, mildew, wax, efflorescence, bond-breakers, and other contaminants.
  • Remove all loose, peeling, or chalky paint by sanding, scraping, or other appropriate methods.
  • Repair all cracks, holes, and other surface imperfections with a suitable patching material.
  • Repaired surfaces should then be sanded smooth and dusted clean. Glossy surfaces should be dulled to provide a roughened surface for good adhesion
Apply With:

Brush, Roller, Airless Spray

Thinning Recommendation:

This coating is intended to be applied without thinning or diluting under normal environmental and application conditions. If necessary to maintain good workability, add up to 1/4 pint (4 fl. oz.) of clean water per gallon of coating.

Health & Safety:

Use in a well-ventilated area. Never scrape old paint without proper protective equipment. Scraping or sanding surfaces of older buildings may release dust containing lead or asbestos. EXPOSURE TO LEAD OR ASBESTOS CAN BE VERY HAZARDOUS TO YOUR HEALTH. Always wear appropriate personal protective equipment during surface preparation, and finish cleanup of any residues by water-washing all surfaces.

In Case of Eye Contact:

Flush immediately with plenty of water for at least 15 minutes and get medical attention.

Avoid prolonged contact with skin. Wash paint from your skin with soap and water. Replace lid on container tightly after each use.

Storage:

CAUTION! Do not freeze. Store in a cool, dry area out of direct sunlight. Protect from elements and from temperatures above 110 °F. Close container tightly when not in use.

Keep out of reach of children

LIMITED LIFETIME WARRANTY:

SC Manufacturing LLC warrants your complete satisfaction with this product from defect as long as you own or reside in your residence when our product has been applied and maintained according to exact label directions.

We do not warrant problems with the product which are caused by factors beyond our control, such as structural defects, damage to the paint film by others, poor condition of the substrate, improper application, etc.

If not satisfied as warranted, return the unused portion, as well as a sales receipt to the place of purchase. You will receive as your exclusive remedy either from a refund of the price paid for the product, or replacement with a product of equal value.

This product warranty specifically excludes labor or cost of labor for the application of any paint and consequential, incidental damages. However, the warranty is only valid if applied by a Shane Coatings™ certified technician.

Some states do not allow the exclusion of consequential or incidental damages, so the limitation or exclusion contained in the above warranty may not apply to you.

This warranty gives you specific legal rights, and you may have other rights that vary from state to state.

Warranty is backed by SC Manufacturing LLC, a subsidiary of The Shane Coatings Company.

Customer Reviews

There are no reviews yet.

Add a review

Your email address will not be published. Required fields are marked *

Our Sustainable Development

Our Sustainable Development Campaign is bringing to light, our business of doing good.
With an ongoing commitment to Innovation serving as its cornerstone.